Technology for Improving Life of Thermal Recovery Well Casing
In steam injection process, casing is heated by steam, the change of casing temperature produces thermal stresses in the casing, the casing deforms when stresses exceed the yield point of its material. Casing failure is becoming increasingly prominent in thermal recovery wells, which severely restricts the development effect of such reservoirs, improving casing life of thermal recovery well has become a urgent problem to be solved. Through on-site survey and analysis, reasons for casing damage were determined as follows: strength change by high temperature, sand flow over of oil formation, poor cementing, unfavorable heat insulation and bad material for casing. In order to improve casing life, the supporting measures are introduced, the measures include pre-stress cementing technology, using casing head, thermal stress compensator, high-performance insulation tubing, high temperature cement slurry system, FRT110H special casing, and early sand control completion technology. Field application of these measures has gotten better effect in Shengli oilfield in recent years, the damage rate of thermal recovery well has decreased obviously, and this can provide reference for the efficient development of similar reservoirs at home and abroad.
Key words: Casing failure; Thermal recovery wells; Special casing; Cementing; Sand control completion
Kaiser, T. M. V., Yung, V. Y. B., & Bacon, R. M. (2005). Cyclic Mechanical and Fatigue Properties for OCTG Materials. SPE/PS-CIM/CHOA International Thermal Operations and Heavy Oil Symposium, 1-3 November 2005, Calgary, Alberta, Canada.
 Kaiser,T. M. V. (2005). Post-Yield Material Characterization for Thermal Well Design. SPE/PS-CIM/CHOA International Thermal Operations and Heavy Oil Symposium, 1-3 November 2005, Calgary, Alberta, Canada
 Gao, B. K. (2002). Practical Model for Calculating the Additional Load on Casing by High Temperature. Oil Drilling & Production Technology, 24(1), 8-10.
 Maruyama, K., & Inoue, Y. (1989). An Experimental Study of Casing Performance Under Thermal Recovery Conditions. SPE Drilling Engineering, 5(2), 156-164.
 Lin, F. L., Chen, M., & Zhang, G. Q. et al. (2007). Casing Failure Mechanism Analysis Induced by Reservoir Compaction and Sand in the Producing Layer. Petroleum Drilling and Production Technology, 29(2), 49-51.
 Li, J., Lin, C, Y., & Yang, S. H. et al. (2009). Analysis on Mechanism of Casing Damage and Strength Design for Heavy Oil Wells. Oil Field Equipment, 38(1), 9-13.
 Zhang, Y., Kuang, Y. C., & Wu, K. S. et al. (2008). Research on Casing Failure Mechanism of Thermal Production Well Based on Finite Element Method. Drilling. Production Technology, 32(4), 102-104.
 Bruno, M. S. (2002). Geomechanical and Decision Analyses for Mitigating Compaction Related Casing Damage. SPE Annual Technical Conference and Exhibition, 30 September-3 October 2001, New Orleans, Louisiana.
 Chen, Y., Lian, Z. H., & Chen, R. M. (2009). Analysis for Casing Safety Evaluation Based on Residual Stress in Thermal Well. Oil Field Equipment, 38(4), 16-19.
 Yang, X. J., Yang, L., & Jia, S. P. et al. (2005). The Finite Element Analysis of the Casing Failure Mechanisms of Thermal Recovery Wells in Sand Production. Oil Field Equipment, 34(2), 19-23.
 Li, W. Z. (2003). The Mechanism and Prevention of Casing Damage in Ultra Thick Oil Well of Shuguang Oilfield. Drilling & Production Technology, 26(2), 55―57.
 Yu, L., Bao, M. (2005). New Technology for Easing Damage Prevention and Cure of Thermal Production Wells in Liaohe Oilfield. Petroleum Exploration and Development, 32(1), 116-118.
- There are currently no refbacks.
How to do online submission to another Journal?
If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:
1. Register yourself in Journal B as an Author
Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.
Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.
We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
firstname.lastname@example.org; email@example.com; firstname.lastname@example.org
Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures
Address: 9375 Rue de Roissy Brossard, Québec, J4X 3A1, Canada
Telephone: 1-514-558 6138