Enhancing Tight Gas Recovery Through Hydraulic Fracture Treatment Design Optimization

M. M. Rahman, H. K. Sarma


Tight and deep unconventional gas reservoirs are becoming targets for development but the conventional approach to develop them is not feasible. In most cases, they cannot be produced economically without hydraulic fracturing. There have been much progress in the overall hydraulic fracturing procedures to stimulate tight formation, but there is still a lack in treatment-design optimization. Some of the currently available commercial software do not take into consideration several key parameters and associated realistic constraints.

An integrated model to optimize hydraulic fracture treatment has been developed to enhance gas production and net present value with minimum treatment cost. This model couples with the industry experience with hydraulic fracture mechanics. Unlike commercial software, important design parameters are included. The free design variables are randomly varied during optimization. The overall hydraulic fracturing design problem is viewed as a multi-objective and multivariate system design problem, which recognizes complex interactions between a hydraulically coupled fracture geometry model, a hydrocarbon production model and an investment-return cash flow model. The integrated model has been successfully applied to a hypothetical deeper tight gas formation to demonstrate its merits. The optimum treatment design indicates a 300% increment in production over 10 years at a lower cost compared to production from non-fractured tight gas sand. This optimization scheme presents a decision support system, which provides a goal-oriented optimum design in a conflicting environment.

Key words: Stimulation; Enhanced recovery; Fracture optimization; Tight gas; Treatment design


Stimulation; Enhanced recovery; Fracture optimization; Tight gas; Treatment design

Full Text:



[1] Aggour, T. M., & Economides, M. J. (1998, February). Optimization of the Performance of High-Permeability Fractured Wells. SPE 39474 International Symposium on Formation Damage Control, Lafayette, Louisiana.

[2] Langedijk, R. A., Al-Naabi, S., Al-Lawati, H., Pongratz, R., Elia, M. P., & Abdulrab, T. (2000, October). Optimization of Hydraulic Fracturing in a Deep, Multilayered, Gas-Condensate Reservoir. SPE 63109 Annual Technical Conf. and Exh., Dallas, TX.

[3] Aggour, T. (2001, March). Optimization Strategies for Hydraulic Fractures in High Permeability Reservoirs. SPE 68131 Middle East Oil Show, Bahrain.

[4] Queipo, N. V., Verde, A. J., Canelon, J., & Pintos, S. (2002). Efficient Global Optimization for Hydraulic Fracturing Treatment Design. J. of Petroleum. Science and Engineering, 35, 151-166.

[5] Jiang, T., Wang, X., & Shan, W. (2003, May). A New Comprehensive Hydraulic Fracturing Technology to Minimize Formation Damage in Low Permeability Reservoirs. SPE 82222 European Formation Damage Conf. and Exh., Hague, The Netherlands.

[6] Jiang, T., Wang, Y., Ding, Y., Shan, W., Wang, X., Zhou, X., & Liu, J. (2003, September). The Study of a New Overall Hydraulic Fracturing Mode in Low Permeable and Unconventional Reservoirs. SPE 84820 Eastern Regional/AAPG Eastern Section Joint Meeting, Pittsburg, Pennsylvania.

[7] Wang, Y., Jiang, T., Ding, Y., Luo, N., Feng, X., Wang, X., & Zeng, B. (2004, November). The Study of Hydraulic Fracturing Expert System in Low Permeable and Complex Reservoirs. SPE 89856 International Petroleum Conference, Puebla, Mexico.

[8] Manrique, J. F., & Poe, B. D. (2005, October). Comprehensive Performance Design Criteria for Hydraulic Fracturing. SPE 96929 Annual Technical Conf. and Exh., Dallas, TX.

[9] Rodgerson, J. L., Lopez, H., & Snider, P. (2006). Unique Multistage Process Allows Pinpoint Treatment of Hard-to-Reach Pay. SPE Production and Operations, 11, 441-447.

[10] Beatty, K. J., McGowen, J. M., & Gilbert, J. V. (2007, January). Pin-Point Fracturing (PPF) in Challenging Formations. SPE 106052 Hydraulic Fracturing Technology Conf., College Station.

[11] Houser, J., & Hernandez, R. (2009, April). Pinpoint Fracturing Using a Multiple-Cutting Process. SPE 122949 Rocky Mountain Petroleum Technology Conference, Denver, Colorado.

[12] Mohsen, A., Ali, M. A., Samiee, R. A., Ibrahim, E., Taha, I. M., & Hamdy, M. (2010, June). Implementation of Pinpoint Fracturing Technique in the Western Egypt Desert. SPE 133864 Production and Operations Conf. and Exh., Tunis.

[13] Goldberg, D. E. (1989). Genetic Algorithms in Search, Optimization, and Machine Learning (pp. 412). New York: Addison-Wesley Publishing Corporation.

[14] Nelder, J. A., & Mead, R. (1965). A Simplex Method for Function Minimization. Computer Journal, 7, 308-313.

[15] Rahman, M. K. (2006). An Intelligent Moving Object Optimization Algorithm for Design Problems with Mixed Variables, Mixed Constraints and Multiple Objectives. Structural and Multidisciplinary Optimization, 32(1), 40-58.

[16] Rahman, M. M., Rahman, M. K., & Rahman, S. S. (2003). Multicriteria Hydraulic Fracture Optimization for Reservoir Stimulation. Petroleum Science and Technology, 21, 1-37.

[17] Rahman, M. M. (2008). Constrained Hydraulic Fracture Optimization Improves Recovery from Low Permeable Oil Reservoirs. Energy Sources, Part A, 30, 536-551.

[18] Rahman, M. M., & Sarma, H. K. (2011, October). Maximizing Tight Gas Recovery Through a New Hydraulic Fracture Optimization Model. SPE 148205 Reservoir Characterisation and Simulation Conf. and Exhib., Abu Dhabi.

[19] Smith, M. B. (1997). Hydraulic Fracturing (2nd ed.). Tulsa, OK: NSI Technologies.

[20] Nolte, K. G., & Smith, M. B. (1981). Interpretation of Fracturing Pressures. J. of Petroleum Technology, 9, 1767-1775.

[21] Valko, P., & Economides, M. J. (1995). Hydraulic Fracture Mechanics. Chichester, England: John Wiley and Sons.

[22] Economides, M. J., Valko, P. P., & Wang, X. (2001). Recent Advances in Production Engineering. J. of Canadian Petroleum Technology, 40, 35-44.

[23] Rahim, Z., & Holditch, S. A. (2003). Effects of Fracture Fluid Degradation on Underground Fracture Dimensions and Production Increase. J. of Petroleum Science and Engineering, 37, 85-99.

[24] Howard, G. C., & Fast, C. R. (1957). Optimum Fluid Characteristics for Fracture Extension. Drilling and Production Practices, 261-270.

[25] Economides, M. J., Hill, A. D., & Ehlig-Economides, C. (1994). Petroleum Production Systems. Upper Saddle River, NJ: Prentice Hall PTR.

[26] Valko, P., Oligney, R. E., & Economides, M. J. (1997). High Permeability Fracturing of Gas Wells. Gas TIPS (Fall), 3(3), 31-40.

[27] Cinco-Ley, H., & Samaniego, F. (1981). Transient Pressure Analysis for Fractured Wells. J. of Petroleum Technology, 9, 1749-1766.

DOI: http://dx.doi.org/10.3968%2Fj.aped.1925543820130502.1032


  • There are currently no refbacks.


How to do online submission to another Journal?

If you have already registered in Journal A, then how can you submit another article to Journal B? It takes two steps to make it happen:

1. Register yourself in Journal B as an Author

Find the journal you want to submit to in CATEGORIES, click on “VIEW JOURNAL”, “Online Submissions”, “GO TO LOGIN” and “Edit My Profile”. Check “Author” on the “Edit Profile” page, then “Save”.

2. Submission

Go to “User Home”, and click on “Author” under the name of Journal B. You may start a New Submission by clicking on “CLICK HERE”.

We only use three mailboxes as follows to deal with issues about paper acceptance, payment and submission of electronic versions of our journals to databases:
caooc@hotmail.com; aped@cscanada.net; aped@cscanada.org

Copyright © 2010 Canadian Research & Development Centre of Sciences and Cultures
Address: 9375 Rue de Roissy Brossard, Québec, J4X 3A1, Canada

Telephone: 1-514-558 6138
E-mail:office@cscanada.net  office@cscanada.org